Chrysler Sailors Forum

sold to very nice man in texas Thanks

sad to say but I need to sell my 26 http://detroit.craigslist.org/okl/boa/1772753935.html

I have the size for the sale
main luff 25' 6 leach 27' foot 7'8
#1 luff 29'3 luff rope is very tight leach is 29'4 foot is 17'9
#2luff 27' luff rope tight leach is 25'4" foot is 12'
#3 LUFF is 17'4 leach is 16'2 foot is 8' 9"

I will be putting all my sails on ebay. I have a main that is pretty dirty but has no rips or repairs to it 4 out of 10.
A 170% that's in good shape clean no rips or repairs about a 6 out of 10
lapper sail I think its a 150 or 135% clean no rips or repairs 5 out of 10
A storm sail with 3 battens ...

I will be putting a roller furler on my 26 I might just convert it to tape or sell it it is a 170 hank on, the guy at the loft by me said it's in good shape but it is a 30+ year old sail pretty clean I also have a main that is very dirty from being left on the boom for 5 years its a little blown out ...

what would you like for the whole thing? Do you have the chrysler gas can?

Thanks to all it's been a labor of love. I have 2 31 batteries and a converter the the microwave needs both batteries to run.

Full Tilt Ijust got around to posting
http://www.flickr.com/photos/gaho1/show ... 960803634/

I just restored my 26 on a trailer so i didn't work on the keel last year. I just pick the boat up with the crane dropped the keel an a trailer then dropped the boat on the boat trailer.I will sand blast then interprotect 2000 then paint with VC17. I would rather do it right the first time

yes it did thank you very much!

I'm started sailing now does anyone know at what toe rail hole should I put the genoa block on a C-26 from the last stantion forward I have a 170 genoa and a 130 I was waiting for a no wind day to try differt spots but it has been blowing pretty hard lately Thanks

I own a c-26 I just re did the boat and didn't find any zincs at all not even on the outboard. It has always been a fresh water boat do I need the zinc?

Great would like to see some pictures, mine sould be i a week I can't wait

I wanted to get into sailing when I went out in a friends boat. Then I did a 12 meter fun race on true north in st, martins, I was hooked I started looking for a boat headroom, swing keel ,easy to trailer the Chrysler 26 fit the bill. One day in may 08 I went to north star sail club off lake St ...

sounds great! I noticed there is a lot owners in the great lakes my boat is in Lake St. Clair would love to meet other owners in the area

I replaced my table leafs on my 26 to match my new custom galley ( photos soon) I have the two side leafs left over,the center looks like a banana but have the laminate for the top. Just pay for shipping and there yours

Thanks for the help

any help would be great!
I was thinking to use some long wood screws to help it out also if ist's wood in there

do you still have the boat. or a contact to the person that does? I need to know what is under the main sheet bridle mounts under the fiberglass I will pay for info.

I do have some photos of them I'll try to post tomorrow. the screws that mounted the blocks on are 10-24, four on each side I'm afraid that they are wood nuts with the little grippers to grab the wood and three are just spinning

does anyone know what is in the main sheet bridle mount on the stock C-26 is inside that hold the blocks down.I made custom risers for a traveler and two screws on one side and one on the other are stripped. I would like to just retap them to 1/4-20 if its a plate I just painted the inside ceiling ...